湖南910 single board equipment

The profiled plate rolled by 910 veneer equipment is not only dignified and elegant, but also beautiful and novel, with flat appearance, uniform ripple, good utilization rate and good production automation

910 single board equipment adopts Taiwan Delta dvp14es host computer, and uses the electronic control system with text screen display, which is easy to operate and easy to use

910 single board equipment uses galvanized steel plate or colored steel plate or aluminum plate of different colors as raw materials. The products produced are used to build various industrial plants, warehouses, external roof panels and wall panels of houses, as well as internal decorative panels or ceilings, so as to increase the beauty of roofs or walls

910 there are two fixing methods for the installation of single board equipment: penetration type and concealed buckle type. Penetrating fixation is a common method for the installation of color steel tile press on roof and wall, that is, the color plate is fixed on the support (such as purlin) with self tapping screws or rivets. Penetrating fixation is divided into wave crest fixation, wave trough fixation or their combination. Concealed fastening of concealed buckle refers to the method of fixing the fabricated concealed buckle matched with the concealed buckle color plate on the support (such as purlin) first, and the female rib of the color plate is toothed with the central rib of the concealed buckle, which is generally used for the installation of roof panels.

features of 910 single board equipment:

1. The first and second generations of "fully automatic molded colored tile equipment" adopt "swing cylinder drive slide", " Swing cylinder " Belongs to "e; Molded color steel tile equipment " Middle is "e; Vulnerable " If the molding speed of the accessories is too fast, the impact force of the sliding table is large, and the cushioning is easy to vibrate, resulting in cracks in the tiles. It is a "stubborn disease" in the first and second generation of colored tile equipment. So the molding speed is up to 6 pieces per minute. And "e; Hj-10 type --- guided four column molding color steel molding equipment "

2. Guided four column hj-10 type -- high-speed new mold color steel Profiler: using a number of technologies, the host "body" is made of "cast steel" without welding, so the whole machine will not be " Welding " Produce "stress" and cause "main engine" fuselage deformation. The "pressure cylinder and main Bush mold" of the main engine is composed of " Guide sleeve " Bind at 120 mm " Four solid guide hydraulic pillars " The "main Bush mold" runs vertically up and down without vertical deviation, which protects the vulnerability of the main Bush mold, Also extended "Main tile mold.

910 operating skills of single board equipment:

1. Before starting the color steel tile press, check whether the equipment and electrical appliances are in good condition, and cut off the power supply when off duty.

2. When the color tile press is running, do not put a shovel or other items into the mixer.

3. If the operator needs to enter the mixer for inspection, cut off the power supply and set up technicians for supervision.

4. The operator should pay attention to the stability of the operating environment. Such as material Bucket, outlet position, etc

5. Non operators cannot operate casually

6. Adjust the amount of water added to each machine according to the moisture content of yellow sand to make the mixture moist and suitable

7. Make sure that the mixing time is not less than 120 seconds each time

8. Make mixing records according to the mix proportion notice

9. After work, clean the excess materials in the machine and conveyor belt in time and wash them away to keep the surrounding clean

910 technical parameters of single board equipment:

length × wide × 6000mm high × 1300mm × 910mm

forming shaft: diameter 70mm 45 # quenching and tempering

forming wheel: material 45 # forging and hard chromium plating

transmission mode: sprocket, chain

motor: 3kw

number of forming rows: 10 rows

fully automatic computer fixed length cutting system:

pump station motor: 3kw four levels

cutting die: Gr12

forming speed: 8-10m/min

pressing thickness: 0.2-0.7mm

pressing width: 1000m