Products
-
湖南Single layer tile press series
-
湖南Double layer tile press series
-
湖南Three layer tile press series
-
湖南Floor bearing plate equipment
-
湖南Glazed tile equipment series
-
湖南Jiaochi equipment series
-
湖南C/z/u-shaped steel forming mac
-
湖南Carriage plate forming machine
-
湖南Anti skid embossing equipment
-
湖南Aluminum magnesium manganese 4
-
湖南Ridge tile forming machine ser
-
湖南Light steel keel machine serie
-
湖南Shearing machine bending machi
-
湖南Rock wool foam integrated sand
-
湖南Rolling shutter door equipment
-
湖南Discharge rack series of hydra
-
湖南Export equipment series
-
湖南Kaiping machine series
-
湖南pipe benders
-
湖南Customize cold bending equipme
湖南C10-C21 single board computer
C10-C21 single board computer adopts the lower five upper four leveling to determine the flatness. It adopts th...
Order
Operation skills for C10-C21 single board computer:
1. Before starting the color steel tile press, check whether the equipment and electrical appliances are in good condition, and cut off the power supply when leaving work.
2. When the shingle machine is running, do not put the shovel or other objects into the mixer.
3. If the operator needs to enter the mixer for inspection, the power should be cut off and technical personnel should be assigned to supervise.
4. Operators should pay attention to the stability of the operating environment. Such as the position of the hopper and discharge port.
5. Non operators are not allowed to operate casually.
6. According to the moisture content of yellow sand, adjust the amount of water added to each machine to make the mixture moist and suitable.
7. Ensure that each mixing time is not less than 120 seconds.
8. According to the mix proportion notice, make a good mixing record.
9. Clean up excess materials inside the machine and conveyor belt in a timely manner after work and flush them clean, keeping the surrounding area clean and hygienic.
C10-C21 single board computer adopts the lower five upper four leveling to determine the flatness. It adopts the secondary forming type to determine the squareness and right angle of the product. The size of the upper side can be made. The equipment and the C-shaped steel produced are squareness, which is the advantages of the industry such as adjustable speed, fast punching, and fast cutting. C10-C21 single board computers are equipped with a lubrication system, which automatically adds oil and lubrication to all load-bearing bearings, transmission gear mechanism motion rails, and other parts during machine operation. Automatic feeding and billet taking work procedure: Mold installation and main machine trial run are the same as above, then start the air compressor, vacuum pump, extruder, tile cutting machine, feeding machine, car box machine, main machine and tile tray conveyor. When stopping, stop the extruder first and then stop other equipment.
1. Before starting the color steel tile press, check whether the equipment and electrical appliances are in good condition, and cut off the power supply when leaving work.
2. When the shingle machine is running, do not put the shovel or other objects into the mixer.
3. If the operator needs to enter the mixer for inspection, the power should be cut off and technical personnel should be assigned to supervise.
4. Operators should pay attention to the stability of the operating environment. Such as the position of the hopper and discharge port.
5. Non operators are not allowed to operate casually.
6. According to the moisture content of yellow sand, adjust the amount of water added to each machine to make the mixture moist and suitable.
7. Ensure that each mixing time is not less than 120 seconds.
8. According to the mix proportion notice, make a good mixing record.
9. Clean up excess materials inside the machine and conveyor belt in a timely manner after work and flush them clean, keeping the surrounding area clean and hygienic.
C10-C21 single board computer adopts the lower five upper four leveling to determine the flatness. It adopts the secondary forming type to determine the squareness and right angle of the product. The size of the upper side can be made. The equipment and the C-shaped steel produced are squareness, which is the advantages of the industry such as adjustable speed, fast punching, and fast cutting. C10-C21 single board computers are equipped with a lubrication system, which automatically adds oil and lubrication to all load-bearing bearings, transmission gear mechanism motion rails, and other parts during machine operation. Automatic feeding and billet taking work procedure: Mold installation and main machine trial run are the same as above, then start the air compressor, vacuum pump, extruder, tile cutting machine, feeding machine, car box machine, main machine and tile tray conveyor. When stopping, stop the extruder first and then stop other equipment.
 |  |
 |  |
